How To Change Tail Light On Hyundai Elantra

Hyundai Elantra Tail Light Bulbs Replacement Guide
How to change a burnt out restriction, rear plow bespeak or side marker light seedling in a sixth generation 2017 to 2020 Elantra.

2018 Elantra Tail Lights
Open Trunk Lid
Material Access Encompass This automotive maintenance tutorial was specifically written to assist owners of the 6th generation (2017, 2018, 2019, 2020 and maybe also the 2021 model year) Hyundai Elantra sedan in changing a burnt out brake, rear turn signal or side mark calorie-free bulb in the tail light housings (or upgrading them to brighter LED units).

Owners of other Hyundai, Genesis or Kia vehicles such every bit the Sonata, Emphasis, Veloster, Ioniq, Kona, Nexo, Venue, Tucson, Santa Fe, Palisade, G70, G80, G90, Soul, Sportage, Niro, Sorento, Telluride, Rio, Forte, Optima, Stinger, Cadenza, K900, Sedona and Seltos may as well find these DIY instructions to be helpful.

The compatible replacement calorie-free bulb part numbers are as follows: Brake # P21/5W (too known as 7528), Rear Turn Signal # 1156A or 1156NA (Bister) and Rear Side Marker # 2825 (likewise known as W5W).

If you would similar to have brighter tail lights, install some P21/5W LED, 1156A LED and 2825 LED bulbs.

The tools needed to remove the tail light housing in order to access and replace the bulbs include a 10mm socket with a 1/4" drive ratchet or a 10mm wrench and possibly a plastic pry bar tool.

The first two steps are to open the body lid so move to the side of the motorcar with the burnt out light bulb.

(If y'all need to replace the bulbs in the trunk lid housing, check out the 2017-2020 Hyundai Elantra Reverse & Parking Light Bulbs Replacement Guide.)

Look within the body and locate the rectangular shaped fabric admission cover attached to the cargo area liner but in front of the tail light housing.

Pull Out Admission Panel
Locate Two Nuts
Loosen Counterclockwise Gently pull the access cover out of the cargo area liner.

Locate the two small nuts that secure the tail low-cal housing to the rear corner of the vehicle.

Loosen the nuts past turning them in the counterclockwise direction with a 10mm socket and a ane/iv" bulldoze ratchet.

I found that using a brusk extension bar made it easier to loosen the basics.

(On some model years, the two nuts may require an 8mm socket instead of a 10mm socket.)

Remove Second Nut
Spin Off By Hand
Two Nuts Removed Spin off the two nuts the rest of the way past paw to preclude them from falling down into the rear bumper cover.

Prepare the two nuts aside in a prophylactic place.

Pull Housing Off Automobile
Tap To Loosen 2 Pegs
Light Housing Removed Carefully pull the tail light housing straight off the rear corner of the vehicle.

The tail low-cal housing is even so held in identify by ii pegs inserted into plastic grommets and a slot attached to the button head of a plastic pop rivet.

If you have trouble loosening the friction fasteners, use a hammer or the handle of a screwdriver to tap on the pegs from within the cargo area.

You can also use a plastic pry bar tool to very advisedly and gently pry along the outer edge of the tail light housing. Avoid using excessive force to preclude from cracking the lens cover.

Once you loosen the friction fasteners, slide the tail light housing straight off the rear corner of the vehicle.

Disconnect Power Plug
Rear Corner of Vehicle
Back Side of Housing Push in the release tab on the electrical connector inside the torso earlier sliding the power plug straight out of its socket.

Gently remove the rubber grommet and the electrical connector from the hole behind the tail lite housing.

Set the tail lite housing down on a soft surface such equally inside the trunk to forbid from scratching the lens cover.

Brake Low-cal Bulb Socket
Push Downwardly & 1/iv Plow CC
Install New Calorie-free Bulb The large grey plastic seedling socket contains the brake (cease lamp) light bulb.

Rotate the seedling socket one/4 plough in the counterclockwise management earlier pulling it direct out of the housing.

Push the sometime bulb down into the socket and rotate it one/4 turn in the counterclockwise direction earlier pulling information technology straight out.

Push a new bayonet fashion number P21/5W calorie-free bulb down into the socket and rotate it 1/4 turn in the clockwise management to secure it into place.

If you would like to accept brighter brake lights, install some compatible replacement P21/5W LED bulbs.

1/iv Plow Clockwise - Lock
Rear Turn Signal Light
Push Down 1/four Turn CC Re-insert the brake light bulb socket back into the housing and rotate it 1/iv turn in the clockwise direction to secure information technology into identify.

The orange plastic seedling socket contains the rear turn signal light bulb.

Rotate the bulb socket 1/four turn in the counterclockwise management before pulling it directly out of the housing.

Push the old calorie-free bulb down into the socket and rotate it ane/4 turn in the counterclockwise direction before pulling information technology direct out of the socket.

Install New Turn Betoken
1/4 Turn Clockwise - Lock
Rear Side Marker Bulb Push a new bayonet style number 1156A amber colored light bulb down into the socket and rotate information technology 1/4 turn in the clockwise management to secure it into place.

If you lot would like to have brighter rear turn signal lights, install some uniform replacement 1156A LED bulbs.

Re-insert the rear turn betoken calorie-free bulb socket into the housing and rotate information technology 1/four turn in the clockwise direction to secure it into place.

The small bulb socket on the outer corner of the calorie-free housing contains the rear side marker bulb.

Rotate the bulb socket one/4 turn in the counterclockwise management before pulling information technology directly out of the housing.

Pull Out Old Light Bulb
Push In New Light Bulb
1/4 Plough Clockwise - Lock Pull the old light bulb straight out of the socket.

Button a new miniature wedge base number 2825 light bulb straight into the socket.

If you would like to have brighter rear side marker lights that volition also last a lot longer before burning out, install some uniform replacement 2825 LED bulbs.

Re-insert the seedling socket into the housing and rotate it i/4 plough in the clockwise direction to secure it into place.

Insert Plug & Wires
Line Up Slot & Pop Rivet
Line Up ii Pegs & Holes Concur the tail light housing near the rear corner of the vehicle.

Insert the electrical connector through the opening in the sheet metallic and through to the cargo area.

Secure the rubber grommet on the wiring loom to the opening in the sheet metal to continue rain water from entering the cargo area.

Line up the slot and 2 pegs on the rear of the tail light housing with the pop rivet button caput and the two small holes on the rear corner of the vehicle.

Secure Safe Grommet
Slide On Tail Lite Housing
Push In Power Plug Advisedly slide the tail light housing back into place on the rear corner of the machine.

Move to the inside of the body.

Button the electrical connector straight into the socket until you hear or feel it "click" securely into place.

Spin On Two Basics
Tighten Clockwise Spin on the two nuts a few turns by hand in the clockwise direction.

Tighten the ii nuts in the clockwise direction with the 10mm socket and a 1/4" bulldoze ratchet until they are snug.

(Some model years may be equipped with 8mm nuts instead of 10mm fasteners.)

Try to avoid over tightening the nuts to prevent from corking the plastic tail light housing.

Replace Access Cover
Access Embrace Secured
Examination New Tail Light Bulbs Button the fabric admission cover back into place on the carpeted trunk liner.

To test the new tail light bulbs, have an assistant stride on the brake pedal, turn on the parking lights and activate the hazard signals.

Cheque out my 2017-2020 Hyundai Elantra Opposite & Parking Lite Bulbs Replacement Guide if you need to modify those bulbs in the light housing attached to the trunk lid.

For more, delight check out all of my 2017-2020 Hyundai Elantra DIY Repair & Maintenance Guides.

Source: https://paulstravelpictures.com/2017-2020-Hyundai-Elantra-Tail-Light-Bulbs-Replacement-Guide/

Share this post